SafetyPulse: ICAM investigation software, by ICAM Australia
SafetyPulse is the investigation software we built for the method we teach. It carries an ICAM investigation from the first report to corrective actions that have been checked and closed, using the same factor codes and the same vocabulary as our courses.
%20(1400%20x%20315%20px).png?width=1000&height=225&name=Untitled%20(1000%20x%20315%20px)%20(1400%20x%20315%20px).png)
Upcoming Sessions
There are no sessions available at this time
One record, in the order the method sets out
We have trained more than 7,500 investigators. Most go back to a workplace where the investigation lives in a Word template, a spreadsheet and a shared drive. The method gets shortened, the evidence gets separated from the findings, and nobody can show whether the corrective actions worked.
SafetyPulse keeps the whole investigation in one record, in the order the method sets out.
One investigation, from the first interview to the signed report
Plan the evidence with PEEPO
People, Equipment, Environment, Procedures and Organisation on one board, planned before collection starts, so the interviews, records and photographs are named before the site is released.
Interview the operator, free recall first
CollectedInterview the day shift supervisor
In progressReview the last 30 days of pre-start checklists
CollectedPhotograph the access ladder and handrails
CollectedObtain weather records for the shift
CollectedRecord ground conditions and lighting
CollectedDoes the working at heights procedure cover mobile equipment access?
CollectedDoes the pre-start require a ladder check?
CollectedReview the roster for the week before
CollectedWere earlier near misses on truck access reported?
CollectedBuild the factual timeline
Every event sits on one line in the order it happened, with the key events starred. Work as intended, work as normal and work as done each have their own lane, so the gaps between them can be seen.
Factual Timeline
TimelineAll 4 lanesGapsHaul truck checked before the shift. Access ladder marked OK.
4 mm of rain recorded. Surfaces across the site become damp, including truck access ladders.
Truck parked at the fuel bay for end of shift refuelling.
Operator opens the cab door and turns to face the ladder.
Foot slips on the fourth step. Operator falls 1.8 m to the ground.
Analyse the contributing factors
Factors recorded across the four ICAM families and held against the evidence behind them: absent or failed defences, individual and team actions, task and environmental conditions, and organisational factors.
ICAM Analysis Overview
13 Total FactorsAbsent/Failed Defences
Individual/Team Actions
Task/Environmental Conditions
Organisational Factors
Link each recommendation to what was found
A reviewer can walk any recommendation back to the finding it answers, and see which findings are addressed and which are not.
Recommendation #1
Inspect the anti-slip treads on every haul truck access ladder and replace any tread worn below the set threshold. Set a tread depth standard and a replacement schedule based on operating hours.
Linked Contributing Factors
Absent/Failed DefencesThe report, assembled from the record
The executive summary, a plain language definitions table, the terms of reference and the severity classification all come from what the investigation already holds. The investigator edits and approves.
Report Preview
Executive Summary
Event: Operator fall from haul truck access ladder
Definitions
Terms used in this report, written for readers outside the safety function.
| Term | Meaning |
| DF - Absent/Failed Defences | Controls that were missing or did not work on the day. |
| IT - Individual/Team Actions | The actions and decisions of people closest to the event. |
| TE - Task/Environmental Conditions | The workplace conditions that shaped those actions. |
| OFT - Organisational Factor Types | The organisational systems and decisions behind the conditions. |
Severity Classification
| Actual Outcome | Medical Treatment |
| Severity Rating | High |
| Credible Worst Outcome | Serious Injury |
| Hazard Category | Working at Heights |
Corrective actions to verified closure
Each action has an owner, a due date and evidence that it was done.
Bowtie barriers
A barrier found failed, missing or degraded in an investigation is linked to that barrier on the bowtie.
Investigation quality scoring
A board can see that investigations are done properly, not just done.
5 Whys for lower-potential events
An investigation steps up to full ICAM without re-entering anything.
The Investigation Assistant
It drafts, checks for gaps and cites the evidence behind every suggestion. The investigator approves every finding.
Phone and desktop
Report events and capture photos, notes and voice in the field, including offline.
Organisations that investigate properly
Organisations that investigate properly and act on what they find.
Training and software together
The courses teach the method. SafetyPulse is where your investigators apply it the next day. If your team has trained with us, the steps, the terms and the factor codes in the software are the ones they already know.
Questions people ask
What is SafetyPulse?
SafetyPulse is incident investigation software built on the Incident Cause Analysis Method (ICAM). It is made by ICAM Australia Pty Ltd.
Who makes SafetyPulse?
ICAM Australia Pty Ltd, the organisation that teaches ICAM. It is sometimes written as SafetyPulse by ICAM Australia, to tell it apart from unrelated products with a similar name overseas.
Does SafetyPulse follow the ICAM method?
Yes. It follows the method as ICAM Australia teaches it: PEEPO evidence planning, a factual timeline, contributing factors across the four ICAM families, and recommendations linked to those factors.
Is our data kept in Australia?
Customer data is hosted in Australia.
Does it work for smaller events?
Yes. Lower-potential events can be analysed with 5 Whys, and stepped up to a full ICAM investigation if the evidence calls for it.
Does the software decide the findings?
No. The Investigation Assistant drafts and checks, and cites the evidence for each suggestion. The investigator decides and approves every finding.
Do we need ICAM training to use it?
Training is not required to use the software, but investigators who know the method get more from it. We offer both.
How do we see it?
Book a demo. A demo runs for 45 minutes and uses the kinds of incidents you investigate.